Hail
Chipped Paint Across the Field
- You See
- Bright metal showing through dents after a storm.
- What It Means
- Each chip leaves steel open to rust. Primer and a full coating cover them before rust takes hold.
Washington, Indiana
Washington Metal Roof Coating Contractor
Coating for Farm Shops, Storage Buildings, and Processing Plants
As a Washington metal roof coating contractor, we check farm, storage, and processing buildings for hail damage and rusted laps, then coat the steel.
- Hail Damage Checked
- Farm And Processing Buildings
- Chips Primed Before Coating
Washington Focus
Washington Metal Roof Coating After Hail Season
What We Look For After a Spring Storm
Washington metal roof coating work often follows a spring storm that left small dents and chipped paint across a farm shop or storage building. The steel is still solid, yet every chip is a spot where rust starts.
We walk the roof after the storm, mark exposed metal and cracked washers, and plan a coating that covers the damage before it spreads.
- Dents and paint chips marked panel by panel
- Screw washers checked for cracks from impact
- Light panels and vents checked for splits
- A thicker base coat where storms repeat
Roof Conditions
Metal Roof Coating Problems on Washington Buildings
Storm damage and age show up together on these buildings.
Hail
Cracked Light Panels
- You See
- Splits or holes in clear ribbed skylight panels.
- What It Means
- Light panels break before steel does. They are replaced to match the rib profile before the roof is coated.
Impact
Cracked Screw Washers
- You See
- Washers split by hail or age, with rust stains below.
- What It Means
- A cracked washer leaks every rain. Screws get new washers and sealed heads.
Moisture
Rust Over Wash Bays
- You See
- Rust at laps above wash bays or grain handling areas.
- What It Means
- Moisture from inside the building attacks the panel underside. Laps above wet areas get extra attention and a check for rust from below.
Age
Split Ridge Vent Covers
- You See
- Cracked or missing covers on ridge and roof vents.
- What It Means
- Vent covers take the brunt of hail. They are replaced and sealed so the ridge stays closed once the field is coated.
Drainage
Water at Lean-To Joints
- You See
- Leaks where a lean-to roof ties into the main building.
- What It Means
- Water collects where two roofs meet. The joint gets new flashing and fabric before the coating ties both roofs together.
Coat Or Replace
Benefits of Coating Your Roof
For a Washington storage or processing building with storm chips, coating protects the steel without new panels.
| What Changes | Coating The Roof | Replacing The Roof |
|---|---|---|
| Storm Damage | Chips primed and covered | Damaged panels replaced |
| Price Range | About $2.50 to $4 per sq ft | About $5 to $8 per sq ft |
| Stored Goods | Stay inside under a closed roof | Moved or covered during the work |
| Impact Resistance | Thicker base coat available | Set by the new panel gauge |
| Light Panels | Replaced to match during prep | Replaced with the new roof |
| Downtime | Equipment keeps moving below | Bays cleared while panels change |
Coating Options
Commercial Roof Coating Options for Washington
Washington buildings mix steel, low-slope, and shingled sections. Here is where each system fits.
Commercial Metal Roof Coating
Main system for storm-chipped steel on shops, storage, and processing buildings.
Silicone Roof Coating
Low-slope office or processing additions where rain sits.
Acrylic Roof Coating
Steep storage roofs that drain fast and need a bright finish.
Spray Foam Roofing
Shops that need insulation over old ribbed metal.
Shingle Roof Coating
Shingled farm offices or front buildings that still lie flat.
Hail Just Came Through?
Chipped paint rusts within a season. Call us after the storm and we will walk the roof and mark the damage.
Call UsHow The Work Runs
Metal Roof Coating Steps on a Washington Storage Building
Storm-damaged roofs get a closer look before any coating goes on.
- 1
Inspect Your Roof
We walk the roof panel by panel, photograph dents and chips, and check washers, skylights, and vents for impact damage.
- 2
Replace Broken Parts
Cracked light panels, split boots, and damaged washers are replaced to match what is there.
- 3
Clean And Prime Chips
The roof is washed, and every chip and bare spot gets rust-inhibiting primer.
- 4
Seal Laps And Screws
Laps get fabric and mastic, and screw heads get sealed to close every leak point.
- 5
Apply A Heavier Base
Roofs that see repeated hail can take a tougher base coat before the finish coat.
Nearby Towns
Nearby Towns We Work In
Washington is one of six towns on our list. Is your building somewhere else? Please call us or send us a message.
Martinsville
Store and office roofs coated in sections during open hours.
Martinsville metal roof coating
Owner Questions
Questions About Metal Roof Coating in Washington
What Washington owners ask after storms and before coating.
Which jobs count as metal roof coating for Washington businesses?
Shops, storage, processing
Farm shops, storage buildings, processing buildings, and stores with steel roofs all qualify. The work covers rust treatment, screw and lap sealing, and a coating system picked for slope and drainage after we look at panel condition and seams.
Where can I get Washington metal roof coating near me?
Call us to schedule
Washington is inside our regular service area. Send a message or call with the address, and we set up a roof walk. Buildings just outside town can ask too, and we tell you right away whether we reach them.
Is there a metal roof coating contractor near Washington for storm damage?
Yes, we cover Washington
We inspect and coat storm-damaged metal roofs in Washington and the surrounding area. A typical job starts with photos of every dent and chip, then repairs to washers and light panels, then primer and coating over the damaged areas or the whole roof.
Does spring hail hurt a coated metal roof in Washington?
It can, mostly on thin films
Large hail can dent the steel under any coating, and thin films crack or puncture where stones hit hardest. A heavier urethane base under the finish coat holds up better on buildings that take repeated storms, and damaged spots can be cleaned and recoated without redoing the roof.
Can you coat over a roof that will get an insurance claim?
Yes, after the adjuster visits
Damage should be documented before any work starts. We photograph dents and chips during the inspection and share them with you. Coating waits until the adjuster has seen the roof, so nothing gets covered too early.
Do coated roofs work on buildings with wash bays or grain handling?
Yes, with checks from below
Moisture rising from inside rusts panels from the underside. We check laps and panel bottoms above wet areas from inside where we can, and the coating on top seals the outside while ventilation handles the inside.
Are farm buildings coated the same way as commercial ones?
Same steps, different staging
Steel farm shops and storage buildings get the same rust treatment, screw sealing, and coating as any commercial roof. Staging changes: we plan around equipment moves, harvest traffic, and stored grain or feed so the work stays clear of the busiest days.
Hire a Washington Metal Roof Coating Contractor
Send photos of storm damage or the worst spots on the roof. We walk the roof and price the coating.